Entering the Chesapeake

Sunrise at Sea
Sunrise at sea off the coast of New Jersey

After leaving Martha’s Vineyard, Idle Queen’s bowsprit pointed across a glassy, starlit sea toward the Block Island Light, and later the powerful beacon at Montauk.  After a couple of days spent waiting for strong headwinds to blow themselves out, we were left with nothing to stir the sea or fill the sails.  Hourly trips to turn the grease cup that lubricates the drive shaft bearing provided a means to mark time on this passage as the engine droned away noisily.  How since we passed Cuttyhunk Island?  5 turns of the grease cup I noted at one point.  There were a few brilliant shooting stars that night, providing some excitement when they left trails glowing in the sky where they cut into the atmosphere.  We carried a fair tide all the way to the Race, thanks to having picked a good departure time and to the engine for keeping the boat moving.

A meaningful amount of wind did not cross the deck until we were on Long Island Sound. I had decided to head up the Sound because a strong cold front was forecast to sweep southward before there was any chance of making it to shelter if we had headed to the south of Long Island, and there was no reason to be caught offshore in the forecast gale that was to follow.

We were hit by the first blast of southwest wind when we were just short of Oyster Bay.  I had really hoped to make it to Port Washington, as it would have left us in a favorable position for continuing with a fair wind later.  Once the wind built enough to leave Idle Queen overpowered with just a double-reefed mainsail and the staysail, I began to have second thoughts about making it to Port Washington.  It’s only 15 miles.  We have a fair current.  We can make it.

It was not to be.  Rain came with curtain of fog and blotted out an overtaking tow that I had been watching that was only at that point about a mile astern.  We have no radar, and it wouldn’t have done us any good as we pitched and heeled anyway.  If I couldn’t see the tugboat’s powerful running lights, they sure couldn’t see the feeble glow from mine.  I estimated visibility at about 50 yards.  Idle Queen may have been lost in the rain and sea clutter on the tugboat’s radar.  Even though they should have passed almost a mile to our north, I didn’t want them worrying about where that sailboat went, so I tacked away to the south, putting us perpendicular to their course and any danger of collision.  With visibility so bad, it was time to seek shelter, so I made for Oyster Bay, where we sheltered for an entire day from the howling wind.

When we headed out the next morning to try to make it through the East River and out to the Atlantic in order to continue south, the wind was down to about 30 knots out of the northwest.  That, however, was enough to make it painfully slow to make it out of Oyster Bay.  Idle Queen is not a powerful sailer to windward–her keel is shallow; she has high freeboard to hold her back; and her sails have assumed a very relaxed shape when compared to the nice foil shapes they had when they were new.  We can’t power very quickly into a blow, either.  The engine is reliable and in good condition, but it is small–we have less than 1.5 hp per ton of boat.  Take a headwind and add a short chop, and the result is slow going for Idle Queen.  It took almost four hours to claw the three miles to windward so that we could make the turn to continue west on Long Island Sound toward the East River.  That put us way behind the tide, so we anchored near City Island to wait for the next ebb to flush us through the East River and down New York Harbor.  We would do that leg at night.

After breaking the anchor out of the thick, oyster-studded mire at City Island, I stood in the cockpit and motored toward the Throgs Neck Bridge.  My hands went numb after just a few minutes, despite doing my best to avoid exposing them to the below-freezing might air.  I needed to frequently pull out my flashlight to check my position and verify the upcoming lights, and the switch on the flashlight was too small to push when my hands were in gloves.  With the exception of a moment’s confusion near Riker’s Island (where a few channels come together), the trip went smoothly.  With a fast-running fair current and many rocks lurking in the dark, it only takes a moment’s confusion for the boat to end up against something solid.  Fortunately, I figured the marks out and avoided getting into shallow water.

We ran the gauntlet between ships, tows, ferries, and patrol craft and made it down New York Harbor to where it meets the sea at Ambrose Channel.  There, I enjoyed the wide, well-marked channel with few background lights to confuse after the hectic hours in the East River and New York Harbor.  The wind was fair and whipping, so I set the staysail.  We sailed into the Atlantic and turned right, making 5 knots with very little canvas set.

Dawn found us well past Sandy Hook.  As the wind lightened, I set first a double-reefed, and later the full mainsail.  Progress was good, but the ride was bumpy, with Idle Queen bouncing uncomfortably down the 4-6 foot swells.  We were moving well and my spirits were high, despite an uneasy stomach.  Maybe it was that can of peaches I ate earlier.  I shouldn’t have felt so queasy given the conditions.

Late that night, with the incredibly huge video screen of Atlantic City still visible, I finally had to give in to my body and void my stomach.  I am not sure what caused me to get sick, but it took a few hours to get over.  Probably something that I ate.  Feeling a bit weak, and with the forecast calling for headwinds the next day, I decided to turn in to Cape May and head up the Delaware Bay.

We fueled up at Utsch’s Marina, where I spent a short while chatting with the owner about the weather and the declining state of the pleasure boating business.  “Ten years ago, all of these marinas had more transients than they could handle,” he said, sweeping his hand through an arc past at least three other big marinas.  “Now, we don’t have half the business we were doing back then.”  He knew that he was part of a dwindling number of family-run marinas, and seemed to indicate that he could already imagine the day when he couldn’t make it pay anymore.  I was thankful to have given him my business, though it was just a small fuel sale.  We continued on our way with some helpful tips about the Delaware Bay and a free cup of coffee.

The fair tide carried us to the Upper Bay, where we anchored not far from a nuclear power plant.  We were completely exposed, with miles of fetch in every direction, but the water was calm by this point.  The whole trip from Cape May had, at the most, about 10 knots of wind, which was on the nose, of course.  After the sun set, the water was glassy.  It was wonderful to be able to catch a couple of hours of sleep before the tide turned once again and we continued on through the Chesapeake and Delaware Canal at night.

Daybreak brought more headwinds.  Fortunately, they were light and we were able to motor the rest of the way to Annapolis without ever having our speed over the ground fall much below 3 knots.  Yeah,  I am happy as long as the boat is at least moving at a good walking speed.  We worked the shallows to avoid the flood tide, and stayed in deep water to get a push from the ebb.  It was about 3 in the afternoon when we motored under the drawbridge to enter Spa Creek.  It was time to take a break…  The forecast called for freezing temperatures and gale-force winds.

Spa Creek
Idle Queen anchored in Spa Creek, Annapolis, MD

It blew hard all day today, but the wind is tapering off now.  With a couple of days rest and freshly-laundered clothes, we are again ready to continue our journey south.  The current plan is to leave tomorrow morning and see how far we make it before the wind turns on us again.

A few photos from Marthas Vineyard follow:

Moon path
Idle Queen’s mast is touching the moon!
Gannon and Benjamin
Gannon and Benjamin
Packet ship sign
Packet ship sign

Writing from Annapolis

The workshop at Gannon and Benjamin in Vineyard Haven
The workshop at Gannon and Benjamin in Vineyard Haven

Idle Queen is anchored in Annapolis, MD.  We are taking a break to rest and wait for tomorrow’s forecast snow to blow through before continuing.  Trip report to follow when I find a faster Internet connection…

On Our Way…

Just a few words here, as I am about to pull anchor to head through the East River, down New York Harbor, and hopefully onward to either Delaware Bay or the mouth of the Chesapeake.

We had an easy run from Martha’s Vineyard most of the way up Long Island Sound before an approaching front brought fog, rain, and 50-mile per hour gusts.  We staggered into Oyster Bay (from where I am writing now) quite overpowered though we were only flying a double-reefed mainsail and the staysail.  There were a few scary moments shortly before we found the harbor when an overtaking tug and barge disappeared into a particularly thick pocket of rain.  They had looked to be passing us to starboard, so I tacked away to head far from the course I anticipated they would continue.  The scary part was that I had no confirmation until the rain let up 10 minutes later.  By then, we were probably 1.5 miles from their track.  Whew.

Now, with a new, strong northwest wind blowing over the island behind which Idle Queen is currently anchored, I see that it is time to go.  This will be a good wind direction for us once we are headed down the New Jersey coast, and it is forecast to remain favorable for the next 48 hours.  Our progress over that time will dictate whether we make for the Delaware or Chesapeake Bay.  I will update when I next find an Internet connection…

Waiting for the Weather

Dreadnought 32 Idle Queen
Idle Queen on arrival in Vineyard Haven

Those of you who have been following Setforsea on Facebook know that we are now in Vineyard Haven waiting for today’s southwesterly wind to turn around to the southeast so that we can quickly cross Block Island Sound and make some meaningful progress on our trip south in search of warmer winter weather.  I have recently been following the pattern of only checking in on the Facebook page, so there is quite a bit there that hasn’t been published here.

Hadley's Harbor
Boathouse on Hadley’s Harbor

There hasn’t been much in the way of sailing travels to write about in the past couple of months, as the time was mostly spent visiting with family and friends, but Idle Queen is now on the move again for more than just daysails.  It feels great to have the bowsprit pointed south; to be poring over charts to pick the next anchorage; and have the day’s activities again dictated by the weather.  Recently, we careened the boat to clean the prop and change zincs; beat down Buzzard’s Bay to Hadley’s Harbor, where we got stuck for two days when an Arctic front brought sub-freezing temperatures, gusty winds, and snow; and then sailed to Martha’s Vineyard where we are waiting on better weather for heading south.

Of course, Idle Queen and her gear weren’t forgotten while she rested on a sheltered mooring through September and October. She was visited almost every day to make sure that she was secure. Her sails were removed and washed, and many other pieces of gear were taken ashore for cleaning. A good portion my time was spent rebuilding the little Dyer “Midget” that I bought to have a hard-bottomed tender. Every piece of the boat needed to be redone, as I had purchased only an empty fiberglass shell, some pieces of wood, and a bag of hardware.  Read about the restoration here.

I put together a video from footage taken during a daysail this summer on Buzzard’s Bay that shows Idle Queen charging right along.  It can be viewed below, or on the Setforsea YouTube channel.

 

Rebuilding the Dyer Dinghy

Dyer Midget dinghy
The newly-rebuilt Dyer on the shore of Little Bay.
Dyer Midget dinghy
The Dyer, as I found her

The little Dyer (actually a Dyer “Midget” low-sheer) was a restoration project that had been started by someone else when I found it.  The disassembly portion of the work was complete.  I had bought a pile of parts with no instructions, leaving me scratching my head over what to do next.

On our way north this summer, we stopped in at the Dyer factory in Warren, RI, to buy pre-bent pieces of wood that would be fashioned into the new rubrail and clamp.  These pieces give the dinghy most of its strength; provide a place for attaching the oarlocks and hanging knees (for the thwarts), and generally hold the boat in its proper shape.  Before departing North Carolina, I had already experimented with trying to bend thin pieces of wood around the fiberglass shell to try to laminate a new rubrail. The thin, unsupported fiberglass hull complained and deformed under the load of trying to bend even 1/8″ wood around its edge. After those efforts, I decided that it would not be worth the time to try to save the cost of purchasing new, strong, steam-bent pieces of white oak from the factory.  Otherwise, I would need to build a support for the hull to hold it in the proper shape with enough strength to form the new rubrails around it.

The stop at the Dyer factory was worth it.  They provided heaps of information about how to go about the reconstruction of my dinghy, gave a tour of the factory working areas, recounted much about the history of the Dyer dinghies, and answered every question that I could come up with.  I took a couple of pictures of some of the construction details that I knew I would have trouble with later, but as soon as I was observed to be taking pictures, I was told that they didn’t want me to take any more.  Dyer doesn’t mind sharing  most of their secrets, but they probably don’t want someone publishing the details.  That is more than fair.  I wasn’t asked to delete the pictures that I had taken, though I had offered to do so, and for that I am thankful, as they did help me work out some details during the rebuild.  I won’t publish the pictures that they let me take, so all of the pictures here are of my own boat at home.  Dyer also provided measurements for the placement of all the hardware in the boat, which was particularly helpful, as I had not seen my dinghy before it had been taken to pieces.

Dyer Midget rubrail
Fitting the new guard at the bow. It doesn’t want to bend like that!

The rebuilding process was not quite as straightforward as I had hoped.  Fitting the new rubrail (the “guard”, which goes around the outside rim of the hull), and clamp (which goes around the inside of the hull) was more complicated than just putting them in place and hand-peening nearly 100 copper rivets.  The new pieces of steam-bent white oak still needed a fair amount of coaxing and a bit of shaping to fit the hull.

Dyer Midget dinghy
“New” transom board made from the old center thwart.

I started by turning the old aft thwart into a new transom by trimming it to size, as the old transom did not come with the boat.  It had presumably rotted away.  The new transom piece is a bit thinner than the original, and has some “character” from its former life as a thwart.  It was bedded in place, but not glued, as the factory told me that gluing can cause problems in the future if the piece ever needs to be replaced again.

Dyer Midget dinghy rubrail
Riveting the new rubrail to the bow

The next task was to fit the new gunwhale clamp and guard.  Dyer provides them as a kit, which is comprised of the wood, copper rivets, a couple of wood plugs and screws, and instructions.  First, I sanded and planed the inside, bottom edge of the forward part of the clamp so that it would fit into place against the compound curve of the hull.  Dyer had instructed me to do this, but I had to remove a bit more material than I would have guessed.  The forward part of the clamp was drilled to accept rivets, using the old holes in the hull as a guide.  The port-side guard was then held in place with “C” clamps and drilled to accept the rivets.  This sounds easier than it was, as the curve at the very end of the bow was tighter than the bend in the new piece of wood.  I bent a few of my small, cheap “C” clamps trying to get enough pressure on that piece to get it firmly into place.  Rivets were placed before fitting the starboard guard, which also resisted a tight fit at the bow.  No matter how I tried, when I put the starboard guard in place, a small gap would open up where the two pieces butted together at the bow, as pressure from the new wood pieces changed the shape of the hull slightly.  In the end, after a few attempts, I got the gap down to around 1/16 of an inch, which I can live with.

Dyer Midget dinghy rubrail
Almost finished fitting the new clamp and guard!

The remaining pieces of the clamp and guard were trimmed, fit into place, drilled, and riveted following the excellent instructions provided by Dyer.  I won’t go into all of the details here, because Dyer has already got this covered.  Fitting the aft sections of the clamp and guard was easy when compared with the frustratingly difficult bow sections.  The whole process took me probably about 30 hours of work spread over about a week.  I had to frequently step back to figure out how exactly to proceed with one detail or another, and the fitting process took me a long time, as I don’t have much experience shaping and working with wood.

Dyer Midget dinghy rubrail
Rubrail complete. Cutting new aft thwart; skeg; etc.

Once the clamp and guard were in place, the little Dyer had some strength to its form and could be moved around much easier than before.  Now it was time to cut new pieces for the aft thwart; skeg; and daggerboard case support.  These were made out of some marine plywood I had left over from another project.  The aft thwart is lightly glassed in place from below with a small amount of tabbing, as I was shown by Dyer, and has a vertical support in the center to transfer loads to the keel.  I had coated the underside of the new thwart with epoxy before tabbing it into place, and I had to use a heater to get the epoxy to cure, as the days were too cold for it to work properly.  This almost caused a disaster, as the thwart warped from the combination of heat and uneven sealing.  Luckily, I caught the problem before the epoxy was hard.  I was able to wedge the thwart back into the proper shape.  Once the epoxy cured, it was fine.  Had I not caught it, I would have had to cut the piece out; clean up all the surfaces, and start that portion of the project over again.

Dyer Midget dinghy rubrail
New skeg almost complete–ready for glass

I built the new skeg from two thicknesses of my piece of leftover plywood.  It was carefully fit to the bottom of the boat.  Further, I protected the boat with mylar tape where the skeg would sit, and then coated it with epoxy; pushed it in place; and let it cure.  This provides a perfect fit and a solid base for the skeg.  Holes were drilled for bolts sent in from the bottom of the skeg.  The aft-most bolt does not go all the way through the skeg, as I couldn’t find one long enough.  Instead, I potted a 3 1/2 inch machine screw in thickened epoxy.  They are backed up by nuts and big fender washers on the inside to avoid over-stressing the hull if a heavy load ever gets placed on the skeg.  The boat showed old signs of stress-cracks in the skeg-attachment area, so I decided on this attachment method, which differs from the factory.  They use screws from the inside of the boat.  The skeg got 4 layers of 6-ounce fiberglass cloth and epoxy on the bottom to protect it from the wear it will eventually see on beaches.  I finished it with white Interlux Brightsides polyurethane.

Dyer Midget dinghy
Fitting all of the hardware. There are hundreds of fasteners in this 7′ 9″ boat!

With the glass-work complete, I moved on to fitting the hardware that attaches the remaining two thwarts into the boat.  I didn’t have bronze screws, so I bought new stainless fasteners.  I wanted the strength of bolts for the hanging knees and breast-hooks, so I sunk washers into the new rubrail.  It would have saved many hours of work to just have sent the bolts in from the outside, but the bronze pieces were all countersunk for screws.  I wanted the strength of good contact with the shoulder of the countersinking, so I sent the bolts (actually machine screws) through from that side.  Each fastener had to be cut to length and the threads cleaned up so that it would thread into its mating nut.

 

Dyer Midget dinghy rubrail
Nuts sunk into the new rubrail

I assembled the whole boat, including the daggerboard case and the piece that ties it to the center thwart, to make sure that everything fit properly.  Then, I took it all apart.  The new wood was all given at least three coats of varnish, and all of the plywood pieces were sealed with epoxy in addition to varnish (or paint for the skeg).  Only then was everything finally fitted with bedding compound.

Dyer Midget dinghy
Finished, and only 74 pounds! (without flotation foam)

 

I am sure that I could have built a simple dinghy for the hours that I put into this project, but now that I have used my “new” Dyer for a week, I feel that it was worth it.  These dinghies have been in production for more than 50 years for good reason.  They are wonderful tenders–lightweight; tough; reasonably fast; and relatively stable while providing good carrying capacity.  The Dyer factory is an outstanding resource, and will provide parts, and answers to any questions you might have if you are ever tempted to do as I did and restore one of their great little dinghies.

View From Aloft- Video of the Great Dismal Swamp Canal

Here’s a unique perspective on the Dismal Swamp Canal–the view from the top of Idle Queen’s mast.  Hope that you enjoy the latest video on the Setforsea YouTube channel!

Update from the Cape

Dreadnought 32 Idle Queen sailing Buzzard's Bay
Dreadnought 32 Idle Queen sailing Buzzard’s Bay

We haven’t covered many miles in the month since arriving in Massachusetts; well, not by sea anyway.  Idle Queen has been sitting mostly idle, tied to a graciously loaned mooring while her crew wonders what hurdles the new US health care law will have us jump through.  That’s not all we’ve been up to, but this has been a time for doing things that don’t often fit into the cruising life–like reading a daily newspaper.  Most of the focus for this downtime has been on trying to clear out the clutter aboard, visiting friends and family, and working on projects like finally putting together the little Dyer Midget that I bought back in North Carolina.

Dyer Midget rubrail
Rebuilding the Dyer–attaching the new rubrail

The Dyer Midget dinghy has turned out to be more difficult to put together than I had originally anticipated, but this is mostly because I feel obligated to rebuild it the way that Dyer intended, rather than just build new parts out of resin and fibers.  Then again, everything takes three times longer than I ever think that it will.  I bought this dinghy knowing that it would be a project.  Someone else had taken it apart with the intent of restoring it, as many of the wooden parts had rotted away to nothing.

Dyer Midget rubrail
Tight-radius curve at the bow of the Dyer

 

Now, the problem with this situation for me is that my woodworking skills are pretty much limited to building stands for outboard engines out of 2-by-6’s and bolts, or using loosely-fitted wood components as reinforcing for things built of fiberglass.  The construction of the Dyer Midget involves closely-fitted pieces and steam-bent wood–both things that I have little experience with.  The biggest problem has been fitting the strong wooden pieces to the fragile, unreinforced fiberglass shell–the floppy fiberglass risks being ripped apart as I torture resistant pieces of white oak into place to reinforce it.  I keep telling myself that I will be rewarded with a tough, light boat by sticking with the wooden parts that the original design calls for, but I originally thought that I would have this project done in a week of spare time.  It has already dragged out to three times my original projection.  While good progress has been made, the end is not yet near.

Cape Cod bay
Cape Cod Bay view from the Canal. It’s getting chilly for swimming.

Autumn has arrived with chilly, clear nights.  Idle Queen is tugging at her mooring.  Soon it will be time to commit to a plan for the winter, and that will probably involve sailing somewhere south to avoid freezing weather.  In the meantime, we have been enjoying occasional perfect sailing days and the beautiful scenery of this part of the New England coast.

Dreadnought 32
Friends with another Dreadnought 32 in the Cape Cod Canal

New Video- Sailing on Narragansett Bay

I have finally had the time to do a bit of video editing and just put up a new short film of Idle Queen sailing on a beautiful afternoon on Narragansett Bay, Rhode Island.

If you enjoy the videos, please subscribe to the Setforsea YouTube channel.  The quality of the recent videos is much better than the older ones thanks to a better camera and the editor finally learning a few things about proper workflow.  There is still plenty of room for improvement–something to look forward to!  Your comments are welcome here or on the YouTube channel.  Thanks.

You can also view the video directly on YouTube in a new window by following this link.

Cape Cod!

Dreadnought 32 Idle Queen
Idle Queen in a sweet, well-protected spot

Well, we made it up to the Cape safely.  When I last left off, we were just getting ready to head out from Hampton, VA.  We were assured of a couple of days of good weather, but after that, there was a strong front forecast to push through the northern waters of our journey, bringing up to two days of contrary winds and unsettled weather.

IMG_0999_2So, here’s the short version of our travels from the time we left Hampton, VA– After leaving the anchorage across from the public pier, we motorsailed in light, but favorable conditions up to New York harbor, where we waited out two days of nasty weather before heading through Long Island Sound.   After motoring through the East River, we grabbed a free town mooring for the night in Port Washington; filled up on overpriced diesel fuel; met some friendly and interesting people; and raised a few eyebrows sailing through the mooring area.  We headed out with a fair tide early the next morning and sailed overnight to Newport, RI, where we dropped the hook and soaked up a little of the “sailing town” atmosphere (or was that just fog?).

Dyer midget parts
Picking up some new pieces for the Dyer dinghy

The next morning, we pushed up to an anchorage near Bristol; and the following day made our appointment to pick up some parts for our Dyer Midget from the factory in Warren, RI.  It was a memorable experience to be able to sail right up to the factory; pick up their guest mooring; and dinghy to their dock to get our parts.  We got a tour of the manufacturing floor and many tips for how to put our dinghy back together properly–I would highly recommend a Dyer for the great support alone.  They freely gave us several hours of their time and answered all of my many questions even though the Dyer that I own is probably 40 years old and was bought at a yard sale.

Dreadnought 32 Idle Queen sailing
Sailing in light air on Narragansett Bay

After loading our parts onto the already overloaded Idle Queen, we dropped the mooring and pushed against the tide for a few miles to overnight in the roomy anchorage in Bristol, RI.  The weather was dreary, so we didn’t really feel like going any farther.  The following day was lovely, though, so we sailed all day and pushed right past Newport to go directly to Monument Beach, MA; taking advantage of the typical Buzzard’s Bay southwest wind to hurry the last half of the passage along.

Dreadnought 32 Idle Queen unload gear
Unloading some excess gear from Idle Queen

Now, Idle Queen is swinging patiently at a mooring while we take care of unloading some of the extra cargo we had carried north; take some time to visit the dentist (Unplanned.  Ouch.); repair the “deflatable” Zodiac; rebuild the Dyer dinghy; and visit the area a bit.

Heading offshore…

Idle Queen will shortly be outbound from Hampton, VA, northbound to…  as far as we can before the weather closes out on us.  We are aiming for Rhode Island, but will stop in to New York harbor if we don’t make good time.

Planning on writing an update soon with pictures from the Dismal Swamp Canal.  I also have some great video from that part of the trip, but haven’t had time to edit and format it yet.  Looking forward to getting that up soon!